Warranty Administation - August, 2000 Labor Time Guide Updates #00-00-89-017 - (Jul 12, 2000)

Table 1:	LTG Update - All Applicable Platforms
Table 2:	LTG Update - C Platform
Table 3:	LTG Update - C/K Platform
Table 4:	LTG Update - C/K - New Body Style - Platform
Table 5:	LTG Update - E Platform
Table 6:	LTG Update - E/J Platform
Table 7:	LTG Update - F Platform
Table 8:	LTG Update - G Platform
Table 9:	LTG Update - G Van Platform
Table 10:	LTG Update - H Platform
Table 11:	LTG Update - J Platform
Table 12:	LTG Update - K Platform
Table 13:	LTG Update - Ksp Platform
Table 14:	LTG Update - M Platform
Table 15:	LTG Update - M/L Platform
Table 16:	LTG Update - N Platform
Table 17:	LTG Update - S/T Platform
Table 18:	LTG Update - U/X Platform
Table 19:	LTG Update - W Platform
Table 20:	LTG Update - Y Platform

Warranty Administration -- August, 2000 Labor Time Guide Updates

1996-2001 Passenger Cars and Trucks

This bulletin addresses changes to the published General Motors Labor Time Guides. These changes (new or revised) are the result of new time studies and/or dealer "Requests For Review" being handled by the GM Service Operations Group. They are effective upon receipt. All changes will appear in the next printing of the Labor Time Guide.

LTG Update - All Applicable Platforms

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
A/C SYSTEM - LEAK TEST DISCHARGED SYSTEM NOTE: This diagnosis time is to be used when necessary to re-charge the A/C system and locate a leak with an electronic leak detector and/or flourescent dye.	N		0.1-0.5	0.1-0.5	0.1-0.5	0.1-0.5	0.1-0.5	0.1-0.5
NOTE: This labor operation is for reference only. The actual time to perform the diagnosis should be included in "Regular Labor Hours" for the repair of the labor operation submitted.
NOTE: If leak can not be found, use labor operation D4450.
A/C SYSTEM - LEAK TEST DYE DIAGNOSIS NOTE: This labor operation is to to be used when necessary to re-charge the A/C system and add flourescent dye. This labor operation was created in the event that a leak could not be found and the customer would bring the vehicle back at a later date.	N	D4450	0.1-0.5	0.1-0.5	0.1-0.5	0.1-0.5	0.1-0.5	0.1-0.5
NOTE: Only the system capacity of R134a refrigerant and one bottle flourescent dye can be charged to the warranty repair order.
*IND: N - New/R - Revised

LTG Update - C Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.3
ADD:
A- Recover/Recharge A/C System								0.5
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE PART GP: 3.130 POLICY: E		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER PURGE VACUUM - REPLACE		J6441	--	0.3	0.3	0.3	0.3	0.3
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.	N		--	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - C/K Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
ARM, PITMAN - REPLACE PART GP: 6.859 NOTE: For check and adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column. THE PREVIOUS "NOTE" NO LONGER APPLIES TO LABOR OPERATION E7900.	R	E7900
C TRUCK			0.4	0.4	0.4	0.4	0.4	0.4
K TRUCK			1.2	1.2	1.2	1.2	1.2
ADD:
A- W/Hydraulic Brake Booster			0.1	0.1	0.1	0.1	0.1	0.1
BEARING, CRANKSHAFT MAIN - REPLACE PART GP: 0.096		J1150
INC: Use of plastic type gauge
NOTE: Applies to V8 Engine, Codes H, K, M, R
ONE BEARING
MANUAL TRANS	R
C TRUCK			6.8	6.8	6.8	6.8	6.8
K TRUCK			6.8	6.8	6.8	6.8	6.8
AUTO TRANS	R
C TRUCK			6.8	6.8	6.8	6.8	6.8
K TRUCK			6.8	6.8	6.8	6.8	6.8
3500 HD	R
AUTO TRANS			4.6	4.6	4.6	4.6	4.6	4.6
MANUAL TRANS			3.8	3.8	3.8	3.8	3.8	3.8
ADD:
A- W/Engine Oil Cooler			0.1	0.1	0.1	0.1	0.1	0.1
B- W/Skid Plate			0.2	0.2	0.2	0.2	0.2
C- To Replace Main Bearings (Each Additional)	R		0.2	0.2	0.2	0.2	0.2	0.2
D- To Replace All Main Bearings	R		0.7	0.7	0.7	0.7	0.7	0.7
E- To Replace Connecting Rod Bearings (Each)	R		0.2	0.2	0.2	0.2	0.2	0.2
F- To Replace All Connecting Rod Bearings	R		1.3	1.3	1.3	1.3	1.3	1.3
G- To Clean Parts On Vehicles Over 30,000 Miles/48,000 Kilometers if Nec			0.2	0.2	0.2	0.2	0.2	0.2
CRANKSHAFT - REPLACE NOTE: Applies to V8 Engine, Codes H, K, M, R		J1200
No Change to "INC" or "PART GP"
C TRUCK	R		7.3	7.3	7.3	7.3	7.3
K TRUCK	R		7.3	7.3	7.3	7.3	7.3
3500 HD			7.7	7.7	7.7	7.7	7.7	7.7
ADD:
A- With A/C			0.6	0.6	0.6	0.6	0.6	0.6
B- With A.I.R.	R		0.1	0.1	0.1	0.1	0.1	0.1
C- W/Engine Oil Cooler			0.3	0.3	0.3	0.3	0.3	0.3
D- To R&R Cyl Head
One			1.5	1.5	1.5	1.5	1.5	1.5
Both			1.8	1.8	1.8	1.8	1.8	1.8
E- To Replace Piston Rings Only (INC: Ream ridge, check all ring clearances and clean grooves as nec).
Each Piston			0.2	0.2	0.2	0.2	0.2	0.2
All Pistons			1.6	1.6	1.6	1.6	1.6	1.6
F- To Replace Rod Only (INC: Ream ridge).
Each Rod			0.5	0.5	0.5	0.5	0.5	0.5
All Rods			3.7	3.7	3.7	3.7	3.7	3.7
G- To Replace Piston (INC: Ream ridge and R&R rod from piston. Check piston for size and wear. Check bore size, taper, and out of round. Check piston fit and all ring clearances).
Each Piston			0.5	0.5	0.5	0.5	0.5	0.5
All Pistons			3.7	3.7	3.7	3.7	3.7	3.7
H- To Clean Part On Vehicles Over 30,000 Miles/48,000 Kilometers if Nec			0.3	0.3	0.3	0.3	0.3	0.3
CRANKSHAFT - REPLACE NOTE: Applies to V8 Diesel Engine, Codes F, P, S No Change to "INC", "PART GP" or "POLICIES"		J1200
LEFT HAND DRIVE			12.9	12.9	12.9	12.9	12.9	12.9
RIGHT HAND DRIVE	R		--	--	11.7	11.7	11.7
No Change to "ADD" Conditions
RADIATOR ASSEMBLY - R&R NOTE: No Change to "PART GP", "POLICY", "INC" or "NOTE"		J3080
GAS	R		1.2	1.2	1.2	1.2	1.2	1.2
DIESEL			0.9	0.9	0.9	0.9	0.9	0.9
NOTE: No Change to "ADD" Conditions
*IND: N - New/R - Revised

LTG Update - C/K - New Body Style - Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE POLICY: E		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER VENT SOLENOID - REPLACE	N	J6441	--	--	--	0.3	0.3	0.3
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.			--	--	--	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - E Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.2
ADD:
A- Recover/Recharge A/C System								0.5
COMPRESSOR ASSEMBLY - REPLACE PART GP: 9.170		D4440	1.2	1.2	1.2	1.2	1.2	1.2
ADD:
A- Recover/Recharge A/C System			0.5	0.5	0.5	0.5	0.5	0.5
B- To Install Liquid Line Filter (THIS "ADD" CONDITION HAS BEEN DELETED)	R
*IND: N - New/R - Revised

LTG Update - E/J Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
NET, REAR COMPONENT CARGO - REPLACE	N	C4610					0.2	0.2
VALVE, EVPORATIVE EMISSION CANISTER CONTROL - REPLACE		J6324	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
*IND: N - New/R - Revised

LTG Update - F Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE - REPLACE	N	D3255						0.3
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.3
ADD:
A- Recover/Recharge A/C System								0.5
PUMP, ENGINE OIL - REPLACE PART GP: 1.652 NOTE: Applies to V8 Engine, Code G and P No Change to "ADD" Condition		J1020
MANUAL TRANS	R		3.8	3.8	5.8	5.8	5.4	5.4
AUTO TRANS			2.2	2.2	4.5	4.5	4.5	4.5
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER PURGE VACUUM - REPLACE		J6441	--	0.3	0.3	0.3	0.3	0.3
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.	N		--	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - G Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.3
ADD:
A- Recover/Recharge A/C System								0.5
*IND: N - New/R - Revised

LTG Update - G Van Platform

OPERATION DESCRIPTIO	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
RESISTOR, BLOWER MOTOR - REPLACE PART GP: 9.275 NOTE: No Change to Labor Operations D1000, D1001 or D1005	R	D1002
A/C GAS			0.2	0.2	0.2	0.2	0.2	0.2
A/C DIESEL			0.4	0.4	0.4	0.4	0.4	0.4
No Change to "ADD" Conditions
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.4
ADD:
A- Recover/Recharge A/C System Without C69, Rear Auxiliary A/C								0.5
B- Recover/Recharge A/C System With C69, Rear Auxiliary A/C								0.7
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.8
ADD:
A- Recover/Recharge A/C System Without C69, Rear Auxiliary A/C								0.5
B- Recover/Recharge A/C System With C69, Rear Auxiliary A/C								0.7
PISTON, ROD AND/OR RINGS - REPLACE PART GP: 0.626 No Changes to "INCs" NOTE: No Change to Labor Operations J1300 or J1301
NOTE: Applies to V8 Engine, Code R
BOTH BANKS	R	J1307	12.4	12.4	12.4	12.4	12.4	12.4
ADD:
A- With A/C			0.7
B- With Rear A/C	N		0.8	0.8	0.8	0.8	0.8	0.8
C- W/Cruise Control			0.3	0.3	0.3	0.3	0.3	0.3
D- W/Engine Oil Cooler	N		0.1	0.1	0.1	0.1	0.1	0.1
E- To Recondition All Valves
One Bank	N		1.4	1.4	1.4	1.4	1.4	1.4
Both Banks	N		2.8	2.8	2.8	2.8	2.8	2.8
F- To Replace Rings Only
Each Additional Piston	R		0.2	0.2	0.2	0.2	0.2	0.2
All Pistons	R		1.3	1.3	1.3	1.3	1.3	1.3
G- To Replace Rod Only
Each Additional Rod			0.5	0.5	0.5	0.5	0.5	0.5
All Rods	R		3.1	3.1	3.1	3.1	3.1	3.1
H- To Replace Piston
Each Additional Piston			0.5	0.5	0.5	0.5	0.5	0.5
All Pistons	R		2.8	2.8	2.8	2.8	2.8	2.8
I- To Clean Parts On Vehicles Over 30,000 Miles/48,000 Kilometers If Nec
Right or Left			0.3	0.3	0.3	0.3	0.3	0.3
Both			0.4	0.4	0.4	0.4	0.4	0.4
VENT, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6389	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
*IND: N - New/R - Revised

LTG Update - H Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.3
ADD:
A- Recover/Recharge A/C System								0.5
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE PART GP 3:130 POLICY: E		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
*IND: N - New/R - Revised

LTG Update - J Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
PANEL/CARRIER ASSEMBLY, INSTRUMENT CONTROL - REPLACE NOTE: No Change to "PART GP", or "INCs"		C2540
CHEVROLET	R		1.9	1.9	1.9	1.9	1.9	1.9
PONTIAC			2.2	2.2	2.2	2.2	2.2	2.2
No Change to "ADD" Conditions
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.8
ADD:
A- Recover/Recharge A/C System								0.5
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6441	0.2	0.2	0.3	0.3	0.3	0.3
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.	N		0-0.3	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
SWITCH ASSEMBLY, AUTO TRANS FLUID PRESSURE - REPLACE	R	K6351	6.3	6.3	6.3	6.3	6.3	6.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).
NOTE: No Change to Remaining "ADD" Conditions.
SHAFT AND/OR SEAL, MANUAL - REPLACE
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours.	R
SHAFT		K6501
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4	R		--	--	--	8.6	8.6	8.6
SEAL		K6529
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4	R		--	--	--	8.6	8.6	8.6
ADD:
B- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
LEVER, DETENT - REPLACE		K6502
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours.	R
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4	R		--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
WIRING HARNESS AND/OR SOLENOID - REPLACE POLICY: E
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours.	R
1 - 2 SHIFT SOLENOID		K6555
ENGINE CODES D & T			6.2	6.2	6.2	6.2	6.2	6.2
ENGINE CODE 4	R		--	--	--	6.7	6.7	6.7
2 - 3 SHIFT SOLENOID		K6556
ENGINE CODES D & T			6.2	6.2	6.2	6.2	6.2	6.2
ENGINE CODE 4	R		--	--	--	6.7	6.7	6.7
TCC PWM SOLENOID		K6557
ENGINE CODES D & T			6.2	6.2	6.2	6.2	6.2	6.2
ENGINE CODE 4	R		--	--	--	6.7	6.7	6.7
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SLEEVE, OUTPUT SHAFT (LEFT) - REPLACE		K6942	6.2	6.2	6.2	6.2	6.2	6.2
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
TRANSAXLE ASSEMBLY - REPLACE PART GP: 4.003		K7000
INC: Cooler line flush, transfer parts, perform Fluid Checking and Functional Test procedures (as outlined in the service manual), and packaging time for Service Replacement Transmission Assembly (SRTA).	R
NOTE: This operation is for transmission/transaxle replacement only. For transmission/transaxle R&R times use operation J1400.
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours.	R
ENGINE CODES D & T
ENGINE CODE 4	R		--	--	--	6.2	6.2	6.2
NOTE: Disassemble, inspect and reassemble add time to be used as needed when it has been determined that the cost of overhaul exceeds the cost of replacement.
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CONVERTER ASSEMBLY, TRANSAXLE - REPLACE PART GP: 4.115		K7020
INC: Cooler line flush, oil pressure test, clean and inspect parts and all necessary measurements and adjustments.	R
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			7.1	7.1	7.1	7.1	7.1	7.1
ENGINE CODE 4	R		--	--	--	6.2	6.2	6.2
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SEAL, TRANSAXLE CONVERTER - REPLACE PART GP: 4.226		K7060
NOTE: Does not include oil cooler line flush or diagnosis time.	N
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.
ENGINE CODES D & T			7.2	7.2	7.2	7.2	7.2	7.2
ENGINE CODE 4	R		--	--	--	5.0	5.0	5.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
PUMP, TRANSAXLE OIL - R&R OR REPLACE		K7121
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.2	8.2	8.2	8.2	8.2	8.2
ENGINE CODE 4	R		--	--	--	7.2	7.2	7.2
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
VALVE ASSEMBLY, CONTROL AND GASKET - REPLACE		K7123
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.6	8.6	8.6	8.6	8.6	8.6
ENGINE CODE 4	R		--	--	--	7.7	7.7	7.7
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SPACER PLATE, CHECK BALL AND GASKET - REPLACE		K7128
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.6	8.6	8.6	8.6	8.6	8.6
ENGINE CODE 4	R		--	--	--	7.7	7.7	7.7
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SPACER PLATE, CHECK BALL AND GASKET - REPLACE		K7221
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.6	9.6	9.6	9.6	9.6	9.6
ENGINE CODE 4	R		--	--	--	8.7	8.7	8.7
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SHAFT, TURBINE - REPLACE		K7222
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
O-RING, TURBINE SHAFT- REPLACE		K7224
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			6.9	6.9	6.9	6.9	6.9	6.9
ENGINE CODE 4	R		--	--	--	6.0	6.0	6.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SHAFT, PUMP DRIVE - REPLACE		K7226
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.1	8.1	8.1	8.1	8.1	8.1
ENGINE CODE 4	R		--	--	--	7.2	7.2	7.2
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SHAFT, OUTPUT - R&R OR REPLACE		K7325
ENGINE CODES D & T			9.6	9.6	9.6	9.6	9.6	9.6
ENGINE CODE 4	R		--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CHANNEL PLATE AND/OR GASKET - REPLACE
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
PLATE		K7461
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
GASKET		K7462
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
ACCUMULATOR, 1-2; PISTON, SEAL OR SPRING - REPLACE		K7465
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
ACCUMULATOR, 2-3; PISTON, SEAL OR SPRING - REPLACE		K7466
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
ACCUMULATOR, 3-4; PISTON, SEAL OR SPRING - REPLACE		K7467
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SPROCKET, DRIVE - REPLACE		K7504
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.9	8.9	8.9	8.9	8.9	8.9
ENGINE CODE 4	R		--	--	--	8.0	8.0	8.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SPROCKET, DRIVEN - REPLACE		K7506
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			8.8	8.8	8.8	8.8	8.8	8.8
ENGINE CODE 4	R		--	--	--	7.9	7.9	7.9
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
LINK ASSEMBLY, TRANSAXLE DRIVE - REPLACE PART GP: 4.131		K7520
ATTENTION: The following "NOTE" has been deleted from this labor operation.	R
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.
ENGINE CODES D & T			8.8	8.8	8.8	8.8	8.8	8.8
ENGINE CODE 4	R		--	--	--	7.9	7.9	7.9
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SUPPORT AND SEALS, DRIVE SPROCKET - REPLACE		K7522
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.6	9.6	9.6	9.6	9.6	9.6
ENGINE CODE 4	R		--	--	--	8.7	8.7	8.7
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SENSOR, INPUT SPEED - REPLACE		K7524
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			7.6	7.6	7.6	7.6	7.6	7.6
ENGINE CODE 4	R		--	--	--	6.7	6.7	6.7
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
HARNESS ASSEMBLY, CONTROL WIRE - REPLACE		K7526
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			7.7	7.7	7.7	7.7	7.7	7.7
ENGINE CODE 4	R		--	--	--	6.8	6.8	6.8
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SUPPORT, DRIVEN SPROCKET - REPLACE		K7529
ATTENTION: The following "NOTE" has been deleted from this labor operation.	R
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.
ENGINE CODES D & T			9.2	9.2	9.2	9.2	9.2	9.2
ENGINE CODE 4	R		--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CLUTCH, SECOND - R&R OR REPLACE		K7531
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.2	9.2	9.2	9.2	9.2	9.2
ENGINE CODE 4	R		--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SPRAG ASSEMBLY, INPUT - REPLACE		K7537
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.8	9.8	9.8	9.8	9.8	9.8
ENGINE CODE 4	R		--	--	--	8.9	8.9	8.9
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
ACTUATOR ASSEMBLY, PARK LOCK - REPLACE
ATTENTION: The following "INC" has been deleted from this labor operation.
INC: Cooler line flush, oil pressure test, setting T.V. cable, clean and inspect parts and all necessary measurements and adjustments.	R
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
NOTE: Select the Operation that best describes the primary cause of failure.
PARKING LOCK ACTUATOR		K7541
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4	R		--	--	--	7.9	7.9	7.9
ADD:
E- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
GUIDE AND SEAL, PARK LOCK ACTUATOR - REPLACE		K7549
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			7.1	7.1	7.1	7.1	7.1	7.1
ENGINE CODE 4	R		--	--	--	5.0	5.0	5.0
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CARRIER ASSEMBLY, REACTION - REPLACE		K7565
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.2	9.2	9.2	9.2	9.2	9.2
ENGINE CODE 4	R		--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CLUTCH ASSEMBLY, REVERSE INPUT - R&R OR REPLACE		K7571
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.4	9.4	9.4	9.4	9.4	9.4
ENGINE CODE 4	R		--	--	--	8.5	8.5	8.5
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
BAND, INTERMEDIATE/4TH - REPLACE		K7573
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.0	9.0	9.0	9.0	9.0	9.0
ENGINE CODE 4			--	--	--	8.1	8.1	8.1
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
SUPPORT, FORWARD CLUTCH - REPLACE		K7577
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4			--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CLUTCH ASSEMBLY, DIRECT AND COAST - R&R OR REPLACE		K7581
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.8	9.8	9.8	9.8	9.8	9.8
ENGINE CODE 4			--	--	--	8.9	8.9	8.9
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
HOUSING, DIRECT & COAST CLUTCH & INPUT SHAFT - REPLACE		K7582
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.8	9.8	9.8	9.8	9.8	9.8
ENGINE CODE 4			--	--	--	8.9	8.9	8.9
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
GEAR, INPUT INTERNAL AND FORWARD CLUTCH HUB - REPLACE		K7583
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.2	9.2	9.2	9.2	9.2	9.2
ENGINE CODE 4			--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CLUTCH, LO ROLLER - REPLACE		K7584
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.4	9.4	9.4	9.4	9.4	9.4
ENGINE CODE 4			--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CARRIER, INPUT - REPLACE		K7590
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.1	9.1	9.1	9.1	9.1	9.1
ENGINE CODE 4			--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
GEAR, REACTION INTERNAL - REPLACE		K7594
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.1	9.1	9.1	9.1	9.1	9.1
ENGINE CODE 4			--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
BAND, LO/REVERSE - REPLACE		K7596
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.2	9.2	9.2	9.2	9.2	9.2
ENGINE CODE 4			--	--	--	8.3	8.3	8.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
DIFFERENTIAL AND FINAL DRIVE ASSEMBLY, TRANSAXLE - REPLACE		K7620
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4			--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
DIFFERENTIAL AND FINAL DRIVE ASSEMBLY, TRANSMISSION - R&R		K7629
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4			--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
DIFFERENTIAL AND FINAL DRIVE ASSEMBLY, TRANSMISSION - R&R		K7629
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4			--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
GEAR, FINAL DRIVE INTERNAL - R&R OR REPLACE		K7750
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			9.5	9.5	9.5	9.5	9.5	9.5
ENGINE CODE 4			--	--	--	8.6	8.6	8.6
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
CASE, TRANSAXLE - REPLACE PART GP: 4.103		K7800
ATTENTION: The following "NOTE" has been deleted from this labor operation.
"NOTE" For check & adjust toe-in, refer to operation E2000 and add the applicable times to the regular hours column.	R
ENGINE CODES D & T			10.1	10.1	10.1	10.1	10.1	10.1
ENGINE CODE 4	R		--	--	--	9.3	9.3	9.3
ADD:
A- With A/C (THIS "ADD" CONDITION HAS BEEN DELETED).	R
NOTE: No Change to Remaining "ADD" Conditions.
*IND: N - New/R - Revised

LTG Update - K Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.2
ADD:
A- Recover/Recharge A/C System								0.5
COMPRESSOR ASSEMBLY - REPLACE PART GP: 9.170		D4440	1.2	1.2	1.2	1.2	1.2	1.2
ADD:
A- Recover/Recharge A/C System			0.5	0.5	0.5	0.5	0.5	0.5
B- To Install Liquid Line Filter (THIS "ADD" CONDITION HAS BEEN DELETED).	R
*IND: N - New/R - Revised

LTG Update - Ksp Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.2
ADD:
A- Recover/Recharge A/C System								0.5
BEARING AND HUB ASSEMBLY, FRONT WHEEL - REPLACE PART GP: 6.307
INC: R&R Caliper with Bracket, Rotor and Dust Shield	R	E2320
RIGHT			0.9	0.9	0.9	0.9	0.9	0.9
LEFT		E2321	0.9	0.9	0.9	0.9	0.9	0.9
BOTH		E2327	1.5	1.5	1.7	1.7	1.7	1.7
SENSOR, CRANKSHAFT POSITION - REPLACE No Change to "ADD" Condition	R	J4355	0.4	0.4	0.3	0.3	0.9	0.9
SWITCH, EVAPORATIVE EMISSION CANISTER PURGE THERMAL VACUUM - REPLACE		J6335	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER PURGE VACUUM - REPLACE		J6441	--	--	0.2	0.2	0.2	0.2
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.	N		0-0.3	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - M Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
VALVE, EVAPORATOR EMISSION CANISTER CONTROL - REPLACE		J6324	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER VENT SOLENOID - REPLACE	R	J6441	--	--	1.6	1.6	1.6	1.6
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.			--	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - M/L Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.2
ADD:
A- Recover/Recharge A/C System Without C69, Rear Auxiliary A/C								0.5
B- Recover/Recharge A/C System With C69, Rear Auxiliary A/C								0.7
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258
Without C69, Rear Auxiliary A/C	--	--	--	--	--	0.5
With C69, Rear Auxiliary A/C	--	--	--	--	--	0.6
ADD:
A- Recover/Recharge A/C System Without C69, Rear Auxiliary A/C								0.5
B- Recover/Recharge A/C System With C69, Rear Auxiliary A/C								0.7
TOE, FRONT - ADJUST NOTE: No Change to existing "NOTES"	R	E2000
M-VAN			0.8	0.8	0.8	0.8	0.8	0.8
L-VAN			0.9	0.9	0.9	0.9	0.9	0.9
ROD, STEERING RELAY - REPLACE PART GP: 6.870		E7980	0.5	0.5	0.5	0.5	0.5	0.5
NOTE: For check and adjust toe-in, refer to operation E2000 and add the applicable time to the regular hours column.	N
ADD:	R
A- To Adjust Toe-In (THIS "ADD" CONDITION HAS BEEN DELETED)
TIE ROD, INNER - REPLACE PART GP: 6.230
NOTE: For check and adjust toe-in, refer to operation E2000 and add the applicable time to the regular hours column.	N
RIGHT		E8040	0.3	0.3	0.3	0.3	0.3	0.3
LEFT		E8041	0.3	0.3	0.3	0.3	0.3	0.3
BOTH		E8047	0.4	0.4	0.4	0.4	0.4	0.4
ADD:	R
A- To Adjust Toe-In (THIS "ADD" CONDITION HAS BEEN DELETED)
TIE ROD END AND/OR ADJUSTER SLEEVE - REPLACE PART GP: 6.233
NOTE: For check and adjust toe-in, refer to operation E2000 and add the applicable time to the regular hours column.	N
RIGHT		E8060	0.4	0.4	0.4	0.4	0.4	0.4
LEFT		E8061	0.4	0.4	0.4	0.4	0.4	0.4
BOTH		E8067	0.7	0.7	0.7	0.7	0.7	0.7
ADD:	R
A- To Adjust Toe-In (THIS "ADD" CONDITION HAS BEEN DELETED)
PLUG, TRANSFER CASE DRAIN - REPLACE	R	K4290	0.3	0.3	0.3	0.3	0.3	0.3
PLUG, TRANSFER CASE FILL - REPLACE	N	K4291	0.2	0.2	0.2	0.2	0.2	0.2
*IND: N - New/R - Revised

LTG Update - N Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
LOCK, COMPARTMENT (INSTRUMENT PANEL) - REPLACE PART GP: 10.266		C2100
MALIBU & CUTLASS			--	0.2	0.2	0.2	0.2	0.2
GRAND AM & ALERO	R		0.2	0.2	0.2	0.6	0.6	0.6
ACHIEVA & SKYLARK			0.2	0.2	0.2
No Change to "ADD" Condition
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.5
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.5
ADD:
A- Recover/Recharge A/C System								0.5
CORE, EVAPORATOR - REPLACE		D3320
MALIBU & CUTLASS	R		--	4.9	4.9	4.9	4.9	4.9
GRAND AM & ALERO			2.1	2.1	2.1	1.3	1.3	1.3
ACHIEVA - 4 CYL			2.1	2.1	2.1
ACHIEVA - 6 CYL			2.1	2.1	2.1
SKYLARK - 4 CYL			2.1	2.1	2.1
SKYLARK - 6 CYL			2.1	2.1	2.1
ADD:
A- Recover/Recharge A/C System	R		0.5	0.5	0.5	0.5	0.5	0.5
INSULATOR AND/OR SUPPORT, REAR STABILIZER SHAFT - REPLACE PART GP: 7.243 NOTE: No Change to Labor Operations E4180 or E4181
BOTH		E4187
MALIBU & CUTLASS	R		--	0.5	0.5	0.5	0.5	0.5
GRAND AM & ALERO			--	--	--	0.3	0.3	0.3
GEAR ASSEMBLY, POWER STEERING - R&R		E9720	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
GEAR ASSEMBLY, POWER STEERING - REPLACE PART GP: 6.508 INC: Transfer outer tie rods. NOTE: For check and adjust toe-in, refer to Operation E2000 and add the applicable times to the regular hours column.	N	E9740
ACHIEVA & SKYLARK			1.2	1.2	1.2	1.2
GRAND AM & ALERO			1.2	1.2	1.2	1.7	1.7	.17
MALIBU & CUTLASS			--	1.7	1.7	1.7	1.7	1.7
CYLINDER, BRAKE MASTER - REPLACE PART GP: 4.650		H0640
MALIBU & CUTLASS			--	0.6	0.6	0.6	0.6	0.6
ACHIEVA & SKYLARK			1.2	1.2	1.2
GRAND AM & ALERO	R		1.2	1.2	1.2	1.0	1.0	1.0
MOTOR PACK (ABS) - REPLACE	R	H2506	0.6	2.0	2.0	2.0	2.0	2.0
No Change to "ADD" Condition
BOOT, PARKING BRAKE HANDLE - REPLACE	N	H2815	--	--	--	0.8	0.8	0.8
WIRES, SPARK PLUG - REPLACE No Change to "PART GP", or "POLICY"
ONE		J4206
EXC ENGINE CODE M, E and J			0.2	0.2	0.2
ENGINE CODE M, E and J			0.2	0.2	0.2	0.3	0.3	0.3
No Change to "ADD" Conditions
SENSOR, CAMSHAFT POSITION - REPLACE POLICY: E		J4350
4 CYL			0.2	0.2	0.2	0.2	0.2	0.2
6 CYL	R		0.8	0.9	0.9	0.9	0.9	0.9
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.			0-0.3	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER VENT SOLENOID - REPLACE	R	J6441	0.2	0.2	0.2	0.3	0.3	0.3
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.	N		0-0.3	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - S/T Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
ARM, STEERING IDLER - REPLACE PART GP: 6.895 NOTE: For alignment times refer to operation E2000 and add applicable times to the regular hours column.	R	E7960
S TRUCK			0.4	0.4	0.4	0.4	0.4	0.4
T TRUCK			0.4	0.4	0.4	0.4	0.4	0.4
ADD:	R
A- W/Skid Plate			--	--	0.2	0.2	0.2	0.2
B- To Adjust Toe-In (THIS "ADD" CONDITION HAS BEEN DELETED).
ROD, STEERING RELAY - REPLACE PART GP: 6.870 NOTE: For alignment times refer to operation E2000 and add applicable times to the regular hours column.	R	E7980	0.6	0.6	0.6	0.6	0.6	0.6
ADD:	R
A- To Adjust Toe-In (THIS "ADD" CONDITION HAS BEEN DELETED).
TIE ROD END AND/OR ADJUSTER SLEEVE - REPLACE PART GP: 6.230 NOTE: For alignment times refer to operation E2000 and add applicable times to the regular hours column.	R
RIGHT		E8040	0.4	0.4	0.4	0.4	0.4	0.4
LEFT		E8041	0.4	0.4	0.4	0.4	0.4	0.4
BOTH		E8047	0.5	0.5	0.5	0.5	0.5	0.5
TIE ROD END AND/OR ADJUSTER SLEEVE - REPLACE PART GP: 6.233 NOTE: For alignment times refer to operation E2000 and add applicable times to the regular hours column.	R
RIGHT		E8060	0.4	0.4	0.4	0.4	0.4	0.4
LEFT		E8061	0.4	0.4	0.4	0.4	0.4	0.4
BOTH		E8067	0.7	0.7	0.7	0.7	0.7	0.7
*IND: N - New/R - Revised

LTG Update - U/X Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.3
ADD:
A- Recover/Recharge A/C System Without C69, Rear Auxiliary A/C								0.5
B- Recover/Recharge A/C System With C69, Rear Auxiliary A/C								0.7
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						0.4
ADD:
A- Recover/Recharge A/C System Without C69, Rear Auxiliary A/C								0.5
B- Recover/Recharge A/C System With C69, Rear Auxiliary A/C								0.7
SUPPORT AND SEALS, DRIVE SPROCKET - REPLACE NOTE: Applies to Auto Trans 4T65E	N	K7522	--	--	--	9.8	9.8	9.8
ADD:
A- To Recondition 3-4 Accumulator			--	--	--	0.2	0.2	0.2
B- To Clean and Recondition Valve Body			--	--	--	1.0	1.0	1.0
C- To Recondition Oil Pump			--	--	--	0.4	0.4	0.4
D- To Recondition Trans Completely (Exc Carrier/Diff Final Drive)			--	--	--	4.2	4.2	4.2
E- To Recondition Carrier/Differential Final Drive Assembly			--	--	--	0.8	0.8	0.8
F- To Clean Parts On Vehicle Over 30,000 Miles/48,000 Kilometers If Nec			--	--	--	0.5	0.5	0.5
*IND: N - New/R - Revised

LTG Update - W Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
MODULE, BLOWER MOTOR CONTROL - REPLACE	R	D0890	--	0.4	0.4	0.4	0.4	0.4
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.			--	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.5
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258
CHEVROLET, PONTIAC, BUICK								0.8
OLDSMOBILE								2.2
ADD:
A- Recover/Recharge A/C System								0.5
COMPRESSOR ASSEMBLY - REPLACE PART GP: 9.170		D4440
ENGINE CODE H			--	--	--	2.1	2.1	2.1
ENGINE CODE K AND 1			0.8	0.7	0.7	0.7	0.7	0.7
ENGINE CODE X			1.1	1.1
ENGINE CODE M, T, J AND E			0.8	0.8	0.8	0.8	0.8	0.8
ADD:
A- Recover/Recharge A/C System			0.5	0.5	0.5	0.5	0.5	0.5
B- To Install Liquid Line Filter (THIS "ADD" CONDITION HAS BEEN DELETED).	R
C- To Install Liquid Line With Filter (THIS "ADD" CONDITION HAS BEEN DELETED).	R
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.			0-0.3	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
GEAR ASSEMBLY, POWER STEERING - REPLACE PART GP: 6.508 NOTE: For check and adjust toe-in, refer to Operation E2000 and add the applicable times to the regular hours column.	N	E9740
ENGINE CODE M, T, J, E, K, 1, H			2.0	1.4	1.4	1.4	1.4	1.4
ENGINE CODE X			2.6	2.6
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BBEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER VENT SOLENOID - REPLACE		J6441	--	0.2	0.2	0.2	0.2	0.2
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.	N		--	0-0.3	0-0.3	0-0.3	0-0.3	0-0.3
*IND: N - New/R - Revised

LTG Update - Y Platform

OPERATION DESCRIPTION	IND*	OP NUM	MODEL YEAR
			96	97	98	99	00	01
			YEAR VIN CODE
			T	V	W	X	Y	1
FILTER, IN-LINE A/C - REPLACE	N	D3255						0.4
ADD:
A- Recover/Recharge A/C System								0.5
FILTER, IN-LINE A/C - INSTALL NOTE: This Labor Operation can only be used with a Compressor Replacement D4440.	N	D3258						2.1
ADD:
A- Recover/Recharge A/C System								0.5
PULLEY, CRANKSHAFT BALANCER - REPLACE NOTE: Applies to V8 Engine, Codes G, P and 5 No Change to "NOTE" or "ADD" Condition	R	J0710	1.3	2.1	2.1	2.3	2.3	2.3
SOLENOID, EVAPORATIVE EMISSION CANISTER VENT CONTROL - REPLACE		J6391	THIS LABOR OPERATION HAS BEEN DELETED FROM ALL APPLICABLE YEARS
VALVE, EVAPORATIVE EMISSION CANISTER VENT SOLENOID - REPLACE	N	J6441	0.4
ADD:
A- Diagnosis Time: You may claim 0.0 to 0.3 hours depending on actual time performing diagnosis.			0-0.3
*IND: N - New/R - Revised

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information.

WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION